Images are for guidance only and might not represent the final product.

Phosphor Bronze Rod (Cu95-Sn5)

Available Configurations

Properties common to all products in this list

Composition: Cu 95/Sn 5 Form: Rod Material: Phosphor Bronze UNS Number: C51000 Commodity: Alloys
Diameter Length Other Variants
2.38 – 101.6 mm 10 – 3000 mm Cu94-Sn6

Need custom configurations? Please contact us.

Phosphor Bronze Rod (Cu95-Sn5) is supplied as drawn to BS2874 PB102 (UNS C51000, EN CW451K). It is selected for machined parts that need strength, corrosion resistance and low friction against steel in a single material. The 5% tin strengthens and hardens the copper and improves its corrosion resistance, while phosphorus deoxidises the alloy to give sound, consistent metal for turning and milling. Bushings and plain bearings carry shaft loads in sliding contact, where low friction against steel limits wear and seizure. Marine fittings and valve stems, discs and seats must resist corrosion in seawater or process water while holding the close tolerances needed for threading and sealing. Worm wheels and gear blanks run against hardened steel worms, where the bronze-steel pairing under oil lubrication resists scuffing. Main users are general engineering, marine, fluid-handling and power transmission manufacturers, along with prototype and research workshops.
Starting at £130.00 each

Key Features

Phosphor Bronze Rod (Cu95-Sn5) is a copper-tin alloy supplied as drawn, selected for combining strength, corrosion resistance and low friction against steel in a single material.

Tin-Strengthened Composition

The alloy contains approximately 95% copper and 5% tin. The tin addition strengthens and hardens the copper matrix compared with unalloyed copper, giving a stronger, harder material while retaining a copper-based composition. Strength and hardness are combined with the alloy's other functional properties, so a single grade can meet several mechanical and environmental requirements at once.

Corrosion Resistance

The 5% tin content improves the corrosion resistance of the copper base, so the alloy performs more reliably than unalloyed copper when exposed to water. Corrosion resistance comes from the bulk composition rather than a surface coating, so it is retained on freshly cut surfaces after turning, milling or threading operations.

Low Friction Against Steel

The alloy has low friction when sliding against steel. In sliding contact this limits wear of the mating surfaces and reduces the tendency toward seizure. Under oil lubrication, the pairing of this bronze with hardened steel also resists scuffing, so the alloy combines a low-friction surface with the strength and hardness provided by its tin content.

Phosphorus Deoxidation

Phosphorus is added as a deoxidiser during melting, removing oxygen from the alloy. Deoxidation produces sound metal of consistent quality throughout the rod, reducing the risk of internal defects. This consistency gives predictable behaviour during turning and milling, with a uniform response from one section of the bar to the next and between successive lengths.

As Drawn Supply Condition

The rod is supplied as drawn, the condition produced by the final drawing operation, and is intended for direct machining by turning and milling. The drawn material, combined with the sound, deoxidised structure of the alloy, allows close tolerances to be held on machined features, including cut threads, without additional processing before machining begins.

Industrial Applications

General engineering, marine, fluid-handling and power transmission manufacturers, along with prototype and research workshops, select this rod for machined components that must meet several functional demands.

✦ Bushings and Plain Bearings
Bushings and plain bearings are turned from the rod to carry shaft loads where a rotating steel shaft runs in direct sliding contact with the bore. General engineering manufacturers use these components to support shafts in machinery and mechanisms, producing the complete part from one material rather than assembling it from separate backing and running-surface components.
✦ Marine Fittings
Marine fittings machined from the rod are used on vessels and in shoreside equipment where parts are exposed to seawater. Marine manufacturers produce threaded fittings and connecting parts that must keep their fit and function over long service periods in wet, saline conditions, where parts are difficult or costly to replace.
✦ Valve Components
Valve stems, discs and seats are machined from the rod for valves handling seawater or process water. Fluid-handling manufacturers rely on these parts to maintain threaded stem engagement and sealing contact between disc and seat over repeated operating cycles, keeping valves controllable and leak-tight throughout their service in marine and process systems.
✦ Worm Wheels and Gear Blanks
Worm wheels and gear blanks are machined from the rod for gears that run against hardened steel worms in oil-lubricated gear sets. Power transmission manufacturers use this bronze-steel pairing in worm drives, where the wheel takes torque from the worm through continuous sliding tooth contact, supporting reliable speed reduction over extended running periods.
✦ Prototype and Research Workshops
Prototype and research workshops hold the rod as stock for producing one-off and small-batch machined parts. Development engineers use it to make trial components and fixtures for evaluation in test rigs, experimental assemblies and pre-production builds, allowing designs to be assessed in the intended material before committing to larger production quantities.

Synonyms

C51000 Phosphor Bronze Rod CuSn5 Phosphor Bronze Round Bar PB102 Phosphor Bronze Rod CW451K Bronze Rod Cu95Sn5 Stick
each

Choose Your Options

Close

Available Configurations

Properties common to all products in this list

Composition: Cu 95/Sn 5 Form: Rod Material: Phosphor Bronze UNS Number: C51000 Commodity: Alloys

We are collecting your products, please wait!...

Shipping restrictions and charges may apply for some hazardous materials.

Tolerances

Rod
Diameter =<10mm ±10%
Diameter >10mm ±5%
Length <100mm ±1mm
Length >=100mm +5 / -1%